Ambient
Lamination

Ambient Lamination

Either stage reverse system or roller system can laminate in the atmosphere without bubbles

KAR02

Features

• Best for producing medium size displays
• Coating with dispenser
• Ambient lamination

More

KAR06

Features

• For small panel
• DAM / FILL Dispense Coating
• Correspond to quantity production by 2 positions
• Coating pattern simple making software is included as standard
• Full support form Installation to starting-up

More

KAR09

Features

• For medium panel
• Slit Coating
• UV Pre-Curing
• Ambient lamination

More

Lamination JIG2 TYPE

Features

• Used to simply laminate 2 adherends using adhesive, etc.
• Since upper stage is clear, it’s possible to check adhesive spread and height adjustment of lower stage can simply be done looking at dial gauge

More

KAR02

Specifications

Item		Standard Specifications	Remark
Products size		～10 inch
Table Pos.		1 Pos.
OCR Coating	Fil coating	Dispenser
	Coating pattern	OCR pattern making support system
	Supply of fill material	Large sized syringe	Option: tank
	Dam coating	None	Option: Dam coating
	Dam cure	None	Option: LED
	Supply of dam material	None	Option: tank
Lamination	Method	Ambient lamination
	Alignment	Aligned by referring to the outline
Thickness measurement for workpiece		None	Option: Automatic
Supply of workpiece		By hand

KAR06

Specifications

Cost-effective

High accuracy by CCD auto alignment

Space-saving design

Item	Standard
Target Size	Minimum 3.5 inch – Maximum 7 inch
Position Lamination Accuracy	±0.05mm
Resin Coating Thickness	50～200μm
GAP Accuracy	50～149μm: ±15μm 150～200μm: ±10%
Coating Volume Accuracy	F.S Under ±3%
Tact	3.5～5 inch: 30 sec 5～7 inch: 40 sec *Depend on resin, viscosity and work type
Power Source	Single phase AC200～240V 50Hz 6kVA
Pressure Air	Clean Dry Air Over 0.5MPaOver 100L/min is required
Vacuum	Installed vacuum generator
Equipment Size	1,620mmW*1,270mmD*1,900mmH
Equipment Weight	Approximately 1,000kg
Equipment Composition	DAM/ FILL coating, CCD auto alignment Work thickness measurement Auto lamination, UV precuring

KAR09

Specifications

Item	Specifications
Size	2550mm(W)x1450mm(D)x2200mm(H) Additional Blower (655mm(H))
Weight	1,300kg
Samples	Upper Glass: Max 240mm x 180mm Lower Glass: Max 226mm x 170mm Resin Viscosity: 3,000-100,000cps
Tact Time	130 sec (Lamination Mode). A-8.9”
Utility	Electric: AC200-220 Clean Dry Air: 5.0NL/min, >0.5MPa
Accessory	Resin Profile Measurement Device
Others	Blower Exhaust: 4m3/min, 60～100℃, 03＜0.1ppm

Lamination JIG2 TYPE

Specifications

Perfect for simple lamination test using optical clear resin and adhesive, etc.

LCM lamination test is also possible by changing upper and lower stages

*We can accept orders and make laminators for work sizes other than the above mentioned

Specification	Description
Parts Size	Max. 12inch
Equipment Outline	505mm(W)×740mm(D)×280mm(H) ※with stage open
Equipment Weight	Apx. 40kg
Utilities	Vacuum: -70kpa 5NL/min ※ Connection: φ6
Parts Thickness	Max. 10mm (total thickness)
Lamination Method	Manual lamination by upper stage turned over
Stage Specifications	Upper stage: Clear acrylic Lower stage: Aluminum（Black alumite treatment）
LCM	Can be handled with lower stage change ※ Option
Alignment Method	No alignment pin, etc. ※ Can be treated separately as an option according to user’s product specs
UV Irradiation Function	N/A ※Upper stage with hole drilling for UV irradiation

More Process

Go